FF-10 Ball Screw Support Unit (Supported end, Flanged, for shaft ⌀12/14/15 mm)
FF-10 MOSIONX support unit: Supported end, Flanged, compatible shaft ⌀12/14/15 mm, bearing 608ZZ. Original MOSIONX, paired with ball screws. In stock.
Key Specifications
| Series | FF |
| Model | FF-10 |
| Type | Supported end |
| Shape | Flanged |
| Compatible shaft dia | 12/14/15 mm |
| Bearing model | 608ZZ |
Dimension Drawing
Drawing data from the original MOSIONX catalog; always use the actual mounting dimensions.
Compatibility
| Compatible shaft dia | Bearing model |
|---|---|
| 12/14/15 mm | 608ZZ |
Model Code Explanation
FF-10 is a Supported end (Flanged) support unit. During installation the fixed end should carry the main axial load; the supported end gives auxiliary support and allows slight axial float.
FAQ
Which ball screws are compatible with FF-10?
Compatible with ball screws of shaft ⌀ 12/14/15 mm mm; match by the catalog dimensional table.
What is the difference between fixed and supported ends?
The fixed end (BK/EK/FK) carries axial load and locates; the supported end (BF/EF/FF) gives auxiliary support and allows slight axial float.
How do I get the 3D / CAD drawing of FF-10?
In the Selector model list, click the CAD/3D link for this support unit to download the original drawing.
Mounting Dimensions & Outline (FF10 · supported end (flanged))
Housing & mounting dimensions
| Item | Value (mm) |
|---|---|
| Shaft dia D1 (bearing bore) | 8 |
| Body depth L | 12 |
| H | 7 |
| F | 5 |
| Pilot dia Dg6 | 28 |
| Flange square A | 43 |
| Bolt circle PCD | 35 |
| B | 35 |
| Mounting hole ØX | 3.4 |
| Counterbore ØY | 6.5 |
| Counterbore depth Z | 4 |
| Circlip | C8 |
| Weight (kg) | 0.1 |
Matching screw shaft-end dimensions
| Item | Value (mm) |
|---|---|
| Suitable screw dia | ⌀12,⌀14,⌀15 |
| D1 | 8 |
| E | 10 |
Dimension codes A / B / C / E / H1 / h / H / L / PCD / Dg6 follow the drawings in chapter G of the MOSIONX 2026 general catalogue; all values in mm, h to ±0.02 mm. Assembly reference: housing bore K7 for the fixed end, H7 for the supported end; coaxiality of the two housings ≤ 0.02 mm; use KM-series precision locknuts to the thread sizes listed above (external 6g / internal 6H). Always confirm against the delivered product.
FF-10 — Assembly & Lock-nut Torque (reference)
The values below are general references for precision lock nuts. Always follow the manufacturer's technical manual; tighten symmetrically and step-by-step.
| Lock nut thread | Reference torque |
|---|---|
| M10 | 18 N·m |
| M12 | 28 N·m |
| M14 | 38 N·m |
| M15 | 46 N·m |
| M16 | 55 N·m |
| M20 | 95 N·m |
| M25 | 180 N·m |
| M32 | 340 N·m |
| M40 | 620 N·m |
For this unit the compatible shaft is 12/14/15 mm; the fixed / supported lock nut thread is approx. M12 with a recommended reference torque of approx. 28 N·m.
FF-10 — Selection & Load Match
- Structure type: Supported end (Flanged) — The supported end mainly provides radial location and rotational support, allowing some axial thermal expansion.
- Matching bearing: 608ZZ, matched to the ball screw's rated speed and axial load.
- Compatible shaft 12/14/15 mm — keep the screw shaft within this unit's range to avoid long overhang and deflection.
- Together with the ball screw and coupling it forms the feed unit; its rigidity directly affects machine positioning accuracy and backlash.
FF-10 — Common Faults & Troubleshooting
| Symptom | Possible cause | Check & remedy |
|---|---|---|
| Bearing noise | poor lube, misalignment, damaged or contaminated bearing | re-align, re-lubricate, replace bearing if needed |
| Axial play | lock nut loose, bearing clearance too large | re-tighten per table, use zero-clearance / preloaded bearing |
| Abnormal heating | over-preload, poor lube, over-speed | adjust preload, improve lube, verify rated speed |
| Housing crack / deformation | uneven mounting face, over-tight bolts, impact | ensure face flatness, tighten to recommended torque symmetrically |
FF-10 — Typical Applications
As the end-support component of a ball-screw feed unit, FF-10 (Supported end · Flanged) is widely used in CNC machine tools, automation lines, 3D printing / precision measuring equipment, semiconductor packaging and transfer robots where stable axial support and high repeatability are required.
FF-10 — Installation & Maintenance
- Mounting face: keep the housing bottom flat and fully seated on the machine frame — no forced tightening that distorts the housing.
- Alignment: keep screw-to-rail parallelism ≤ 0.02 mm/m to prevent eccentric load and abnormal wear.
- Tightening: tighten the lock nut symmetrically and step-by-step per the table above.
- Lubrication: re-grease the bearing per duty; use the right grade for high speed or clean rooms.
- Protection: in dusty / chip environments add a cover to extend bearing and screw life.
Further Reading: Support Units & Selection Guides
Need to choose shaft diameter, lead and precision grade (C5/C7/C3), or learn about mounting torque, pre-stretch and troubleshooting? We have prepared complete technical guides:
Support Units OverviewSupport Unit Selection & MountingTroubleshooting